Mixing & curing
Why does cement harden—and why does concrete need curing?
Cement hardens through a chemical reaction with water called hydration. Concrete curing protects the moisture and temperature conditions that allow this reaction to develop the intended properties. Letting fresh concrete dry out quickly can work against that process.

- 01
Mix
Cementitious materials meet the mixture’s controlled amount of water.
- 02
React
Hydration forms binding products as the concrete develops strength.
- 03
Cure
Maintain the specified moisture and temperature conditions.
Hydration and drying are different processes
When cement and water are mixed, reaction products form the binder that holds the concrete's aggregates together. Hydration can continue as conditions permit. Drying means moisture is leaving the material. These can happen at the same time, so a dry-looking surface does not tell you how much strength the concrete has developed.
That explains an apparent contradiction on site: dry cement bags must be protected from moisture during storage, while freshly placed concrete needs proper curing after it has been mixed and finished. Water entering stored cement can damage the product before it is used. In the concrete mixture, water has an intentional role.
Further detail: American Cement Association — Cement & Concrete FAQ; Heidelberg Materials — Common Cements SDS, June 2025
Curing water is not permission to add extra mixing water
The mixture is proportioned with a controlled amount of water. Uncontrolled extra water added to make it easier to place can reduce performance. Some measured jobsite adjustment may be permitted within the approved mixture's limits, but that is a separate decision from curing.
Curing is about maintaining suitable conditions after placement. Depending on the work, specified methods may retain moisture with coverings or a suitable curing compound, or maintain it with an appropriate water-curing method. Choose and prepare the method before the pour.
Further detail: NRMCA CIP 26 — Jobsite addition of water; NRMCA CIP 11 — Curing in-place concrete
What should the crew arrange before starting?
Know who will handle curing, what materials are ready and how the exposed surfaces and edges will be protected. Check that the chosen method suits the finish and any later coating or flooring. If a wet covering is part of the plan, it must continue doing its job; an occasional splash followed by repeated drying is not the same process.
Hot weather planning also needs to consider wind and humidity. A surface can lose moisture while the concrete is still being placed and finished. The crew may need evaporation protection during that period, followed by the specified curing method. These are related tasks with different timing.
Further detail: NRMCA CIP 11 — Curing in-place concrete; NRMCA CIP 12 — Hot-weather concreting; NRMCA CIP 5 — Plastic shrinkage cracking
When does curing begin, and when can it stop?
Prepare to protect the surface during placing and finishing, then begin the selected curing method at the appropriate stage without damaging the finish. Follow the project's method and duration requirements; cement type, conditions and the specified performance matter. A universal number of days cannot replace those requirements.
Finishing requires its own judgment. Working surface water into concrete or adding water to help troweling can damage the surface. Curing should follow the proper finishing sequence rather than being confused with that shortcut.
Further detail: NRMCA CIP 11 — Curing in-place concrete; NRMCA CIP 14 — Finishing concrete flatwork
Does “hard enough to walk on” mean it is ready to load?
No. A surface observation does not establish structural capacity. Concrete-strength assessment uses the relevant tests and project criteria; laboratory-cured and field-cured specimens have different purposes. Loading, formwork removal and later construction need the responsible project team's requirements.
Further detail: NRMCA CIP 35 — Testing compressive strength of concrete
Common question
Does concrete gain strength just by drying?
Cementitious materials react with water through hydration. Curing maintains suitable moisture and temperature so the intended properties can develop.
Sources & further reading
- American Cement Association — Applications of cement
- American Cement Association — Cement & Concrete FAQ
- Heidelberg Materials — Common Cements SDS, June 2025
- NRMCA CIP 26 — Jobsite addition of water
- NRMCA CIP 11 — Curing in-place concrete
- NRMCA CIP 12 — Hot-weather concreting
- NRMCA CIP 5 — Plastic shrinkage cracking
- NRMCA CIP 14 — Finishing concrete flatwork
- NRMCA CIP 35 — Testing compressive strength of concrete
